Dx80 User Configuration Tool V2 Manual
FCT - Festo Configuration Tool Application to convert FCT components for the device family CMMP-AS from version 1.x or 2.x to the latest version 2.x Application to convert FCT components for the device family CMMP-AS from version 1.x or 2.x to the latest version 2.x. Connect the provided power adapter and cable (B) between the DX80 2 and a power socket. 5.Pull the foot stand, set the DX80 in an upright position, and adjust the angle. The foot stand is stiff to open at first. To use the same network wall socket for both your computer and DX80. Banner DX80 Installation & Operation Manual. For DX80 configuration commands and DX80 user commands refer to the DX80 Interface Protocol document. 3.5 Front Panel Operation The front panel rotary switches and push button switches control the display information and configuration of the DX80 devices. The flow diagram below. Wireless products from Banner connect remote assets with the people who manage them, enabling real-time monitoring and management of equipment and conditions in difficult-to-access locations or where wired solutions are impractical, ineffective or cost-prohibitive. View online or download Cisco TelePresence DX80 User Manual, Installation Manual. Manuals and User Guides for Cisco TelePresence DX80. We have 10 Cisco TelePresence DX80 manuals available for free PDF download: Reference. Administrators Working With The Setup And Configuration Of What's New In CE8.3 6.
SureCross DX80 and Performance DX80 Product Manual 6.1.2 Gateway with Multiple Nodes (DX80) In this configuration, the Gateway is the master of the wireless network. Configure this network using the User Configuration Tool (UCT) and RS-485 to USB adapter cable. The UCT is used to map inputs and outputs between Nodes and Gateways.
SureCross User Configuration Tool
The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-
less network, view I/O register values graphically, and set system communication pa-
rameters when a host system is not part of the wireless network.
The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt
radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-
mation between your computer and the Gateway. Download the most recent revi-
Installation
The User Configuration Tool uses a USB to RS-485 converter cable to connect a SureCross Gateway to a USB connection on a comput-
er. Once connected, the User Configuration Tool will configure the one-to-one I/O linking and system polling parameters of the wireless
system.
Software
Before connecting a USB device, first download and run the 81398 DX80 User Configura-
tion.MSI program from Banner Engineering Corp's website (
). The program 81398 DX80 User Configuration.MSI installs the User Configura-
tion Tool and the driver for the Banner USB/485 converter cable (BWA-HW-006 and
Dominions 4 manual download. BWA-UCT-900).
If the USB device is connected while loading the software, the driver installation may not
finish properly.
Hardware Connection
To connect a SureCross wireless Gateway to a computer:
1. Complete the software installation first. The program 81398 DX80 User Configuration.MSI installs the User Configuration Tool and
the driver for the Banner USB/485 converter.
2. Connect the USB end of the Banner USB/485 converter to a USB port on the computer. The computer should recognize the Ban-
ner USB/485 device.
3. Connect a Banner wireless Gateway to the Euro-style connect end of the Banner USB/485 converter. The Gateway device powers
up.¹ When using a third-party USB/485 converter, manually wire the communication and power connections. Refer to Banner’s
Gateway datasheet for the wiring pinout configurations.
4. Launch the User Configuration Tool. The program auto-detects the USB port and the SureCross Gateway; the status bar at the
bottom of the screen should indicate READY.
5. Use the Setup tab to select a USB port and baud rate if the SureCross Gateway is not automatically detected. The Gateway’s
factory default baud rate is 19.2k, 1 stop bit, no parity.
If you have more than one system connected to your computer, manually override the settings using the pull-down menus and clicking
the Connect or Disconnect buttons.
¹ The Gateway will not remain powered up until the computer recognizes and configures the USB port. After plugging the USB/485 con-
verter into the computer’s USB port, wait about 10 seconds for the Gateway to be powered (LED 1 solid green).
For most of the UCT screens, a grayed box represents a parameter read from the device while a white box is a parameter entered by the
user.
Rev. G
www.bannerengineering.com - tel: 763-544-3164
Cisco Dx80 Setup Guide
3